Church Sound

Supported By

Church Sound: Top 10 Worship Audio Line Check Problems

When we know what to expect, we can view these problems as mere "speed bumps" rather than disasters.

Do you panic when you don’t get a signal from the stage? “Why can’t I hear the singer!?!”

No more worries…this list explains the common line check problems and how you can fix them, meaning less time spent on line checks and more time making the band sound great!

Doesn’t that sound better than “oh no, what do I do?”

1. Bad Cable

Cables goes bad and if you don’t test your cables on a regular basis, then the issue will most likely show up during a line check. Or, worse, during the service!

A standard issue cable tester can tell you when a cable has gone bad and the issue with the cable. Keep spare cables of all types because you will need them. On a related note, having the right tools like a line tester helps a lot.

2. Bad Connection

Connectors aren’t always pushed all the way. Typically I see this with guitar cables into the guitars or cables into guitar pedals and DI boxes. A simple reseating of the plug should resolve the problem. This goes for all cable connections including XLR, TR, and TRS.

3. Dead Batteries

These might be in an effects box or, where I usually see it, in the onboard EQ/Amp in an acoustic guitar. Keeping a few 9V batteries in the booth comes in handy in these situations.

4. Improper Wiring

Was A plugged into B, not C? Following the signal from the source to the mixer, you should be able to find where the wires are plugged into the wrong place. Often times the issues is as simple as an input being plugged into an output.

We, in the sound booth, see everything coming into the sound booth. Musicians, on the other hand, see wires coming to the stage. Fix the wiring and then educate the musicians if they do any of their own setup.

5. Poor Microphone Location

While you might see a signal, if it’s not in the right location, you might not get enough signal for proper gain structure.

You might not even get a signal because the microphone is too far away. I can see this point as more of a sound-check issue but I say the sooner you can resolve it, the better

6. Broken Equipment

Be it an active DI box or a microphone, equipment will break and you have to be ready for it. Keeping extra equipment around does pay off. Replace any equipment that is “just hanging in” before it breaks.

If it works “most of the time” then it’s unreliable and needs replacing. You don’t want to spend your time mending equipment each week when it could be better spent on the sound check.

7. Improperly Labeled Channel

Of course there’s no signal, nothing is in that channel! Sometimes mistakes are our own fault. Just fix it and then ask the person on stage to try again. If they ask what was wrong, just say it was a board problem.

8. No Signal From The Guitarist/Bassist

This generally happens when they turn down their volume pedal, have their setup set for tuning, or have done something else to disable their rig from sending a signal.

Ask them to check their volume pedal and any effects board options like being set to tune or mute. The increase in use of digital effects pedals in the church environment means an increase in the likelihood of this issue occurring.

9. The Pastor Wants To Add A Video

Hey, this stuff can fly in at any time. I’m just sayin’. . .

10. Bad Mixer Channel

This is the most frustrating because it will result in money and probably require a substitute mixing board for a while. When it does happen, try another channel and mark the channel as bad. Definitely escalate this issue up the chain o’ command ASAP.

I remember freaking out when I couldn’t get a signal from the stage. I thought there were so many possible problems and I had no idea where to start. It’s great being on the other side of that and knowing it’s usually a simple solution. And I think that’s how most audio problems should be seen.

The solutions to most line check problems aren’t complex. However, knowing what can go wrong, you can now provide solutions much faster.

Line check problems aren’t the end of the world so don’t treat them that way. Knowing what to expect, you can view these problems as speed bumps.

This article provided by Behind The Mixer.

Study Hall Top Stories

Supported By

dBTechnologies is an Italian-based speaker manufacturer, leading in the Touring & Live sound market by providing innovative audio solutions. Their flagship ViO series is made up of an entirely active/self-powered series of loudspeakers. The dBT lineup also includes passive loudspeakers, software, and amplifiers, all delivering uncompromising performance. dBTechnologies speakers headline some of the largest festivals and concerts worldwide, setting standards in both Live and Installation markets.