Study Hall
Sponsored by
Audio Technica

Are You Confusing Polarity With Phase?

Mythology runs rampant on the meaning and the use of that switch with the “∅” symbol. It may be (mistakenly) labeled "phase."

By Curt Taipale May 11, 2018

This article is provided by Church Soundcheck.com.

On most audio consoles above a certain price point, there is a button on each channel with the “∅” symbol. It may be (mistakenly) labeled “phase.”

Mythology runs rampant on the meaning and the use of that switch, and most of that confusion is steeped in stories told by someone who didn’t understand it to others who understood it even less.

That misunderstanding leads to a statement that I still hear today – “inverting the polarity is the same thing as the signal being 180 degrees out of phase.”

The terms “phase” and “polarity” refer to two different things and cannot be used interchangeably.

Figure 1. Sine Wave in Polarity (1.5 cycles)

“Phase” implies a shift in time relative to some reference, while “polarity” is simply a reversal of the positive and negative terminals of an audio connection.

That could mean swapping pins 2 & 3 on an XL connector, the tip & ring connection on a TRS connector or the plus & minus leads on a loudspeaker terminal.

As you can see from these two graphs, nothing has changed with time. Figure 1 shows our friendly sine wave test signal in proper polarity, and Figure 2 shows the sine wave signal out of polarity.

Figure 2. Sine Wave Out of Polarity

So let’s clarify. It is more properly termed a “polarity” switch because all that the button does is reverse the wiring between pins 2 and 3 at the XLR input on that particular channel. It does not affect the phase. I know that many of the engineering guys at the manufacturers still call it a “phase” button, but they should know better.

When one looks at a graph of, for example, a sine wave, with the signal delayed in time by 180 degrees, it looks like the polarity has been reversed. And that is probably where the misunderstanding begins. If we don’t see that the signal has been delayed in time, then we could be misled to believe that polarity and phase are the same.

Under what conditions would a sound operator choose to push that polarity switch? Rarely.

Figure 3. Sine Wave (The red trace is delayed by 90 degrees.)

But here’s one that may help to know. Let’s say that you have decided that you want to double-mic the snare drum, with one mic on the top head to capture the main “body” of the sound, and a second mic on the bottom head to get the “snap” of the snares.

When you think about it, you realize that the acoustic energy reaching the top mic when the drum head is hit (down first) is roughly the opposite condition for the acoustic energy received at the mic on the bottom head.

If you don’t invert the polarity of the mic on the bottom of the snare, the sound will seem thin because the low frequencies are canceling; just press the polarity switch on the channel with the bottom snare mic and the snare will sound “fat” again.

Figure 4. Sine Wave (The red trace is delayed by 180 degrees.)

I share a couple of stories in another one of my articles where that switch came in handy, but those were cases where something was miswired. In one case it was a mic cable that had been wired wrong, and it was a situation where changing the cable at the moment wasn’t possible. In multiple other cases the polarity reversal was in a new unit that was shipped from the manufacturer! It happens.

Just remember that the “phase” switch on your console input channel does not “shift the phase by 180 degrees” because that would involve a shift in time. It is nothing more than a polarity reversal. And from this day forward, start calling it a polarity switch rather than a phase switch!

Read the original article here.


About Curt

Curt Taipale
Curt Taipale

President, Taipale Media Systems
 
Curt Taipale of Taipale Media Systems heads up Church Soundcheck.com, a thriving community dedicated to helping technical worship personnel, as well as the Church Sound Boot Camp series of educational classes held throughout the U.S.
Tagged with:

Subscribe to Live Sound International

Subscribe to Live Sound International magazine. Stay up-to-date, get the latest pro audio news, products and resources each month with Live Sound.