By Mike Sokol • December 18, 2018 Some of the most frequently asked questions we get have to do with equalization: “What does it do?” “When and how do I use it?” For whatever reasons, most church sound staffs desperately want to put EQ to the test and into action. Perhaps it’s that adjusting equalization controls provide immediate sonic response — for better or worse, you can instantly hear what you’ve done. Equalization can be used in different ways, including: musically (that is, to “sweeten” certain frequencies of an instrument/vocal so that it is smoother sounding or more present in the overall mix); correctively to make a voice or instrument sound more like it should when inadequate microphones, acoustics or the instrument/voice itself needs help; or creatively as a special effect to make voice/instruments sound unnatural and otherworldly, very different from the original sound source. Provided by Live Sound Advice. We usually don’t want to create such sounds during services, though, as we want to understand what’s being said, and instrumentation usually plays a supportive role rather than an outrageous-sounding feature role. In the church, generally, EQ is used to modify a voice/instrument so it is clearer and more representative of the original sound source. But suppose your original sound source is lacking depth or presence? Well, proper equalization can also correct a potential dilemma, such as making a nasally, bottom-heavy or thin voice sound more “natural” and thus, more intelligible. What is Equalization? A simplistic explanation of EQ is essentially the boosting/cutting of specific frequencies so that a sound source sounds more like itself despite acoustic, microphone or instrument or vocal shortcomings. In essence you are adding or subtracting volume to specific frequencies. You can make people and instruments sound muddy and dark or thin and brittle. You can also by raising the level of specific frequencies create lots of feedback. That’s one major reason why you need to be careful when equalizing sound sources. Now, of course, in order to properly adjust a voice/instrument via EQ you need to know what that sound source sounds like naturally, and if your microphones happen to boost or cut particular frequencies as part of their design. This is critical to your EQ success: know your sound source. Most church folks I speak with don’t really know what the guitars, keyboards or choir voices sound like naturally, without sound reinforcement, and, therefore, can not adjust EQ to help solve an audio challenge. They have no starting point of reference. What to do? Make it a point to rehearse with your choir and praise band. Ask the pastor if you can listen while a sermon is being rehearsed. In short, sit and listen so you learn what everything – voices and instrument – sounds like in the sanctuary or fellowship hall without the support of the sound system. Now you have a reference point. In addition, learn the frequencies of the church instruments and voices. Equalization controls cover a broad spectrum of frequencies, while most instruments and voices cover narrower spectrums. This means that boosting or cutting certain frequencies of certain sound sources may do nothing, or worse, may create problems, such as feedback. Those frequencies you’re boosting/cutting simply may not exist in that particular sound source. Don’t, for example, waste your time trying to boost a low-end 200-Hz frequency on a piccolo. It isn’t there. The frequency chart like the one to the left details the frequency ranges musical instruments and the human voice produce. Study the chart (click to enlarge it), make copies and hang it in the sound room for reference. Once you know what instruments and voices are supposed to sound like you’ll be able to makes EQ adjustments quickly and effectively. click to enlarge Note that some consoles, according to country of origin, will have the “EQ”, “EQ On” or “EQ In” (active) button set differently — on some the EQ will be active when the button is in the Up position (out), while on others EQ will be active when the button is in the Down position (in). Keep your owner’s manual handy. Use the EQ In/Out button to compare what affect your equalization adjustments have created to the overall sound. Let’s look at just some basic EQ terms and controls common to many consoles: —Low-Pass Filter: Insert this filter into circuit to allow low frequencies to pass into the sound system. Also called a High Cut Filter. —High-Pass Filter: Insert to reduce low-frequency rumble (e.g., from heating & air conditioning, moving pianos, footsteps on stage). Essentially shouts out low frequencies below a variable set point and allows frequencies above (higher) that point to pass through. Also called a Low Cut Filter. —Sweepable EQ: Generally used in the mid frequencies. Set a certain amount of boost/cut and then “sweep” through the frequencies to find the sweet or sour frequency. —Parametric EQ: Found in more sophisticated mixing consoles parametric equalizers offer more possible frequency adjustments, with separate control for center frequencies, bandwidth (difference between the upper and lower cutoff frequencies) and boost/cut parameters. Always start with EQ controls set to “out” or off. Always check that EQ is out of the circuit before you start a service or rehearsal. Start each service with EQ “normaled,” which means out of the circuit, and all EQ controls set to off. That way you won’t inadvertently hit the button and send the congregation running for the exits. Generally, the noon or 12 o’clock position (zero) on the knob indicates no cut or boost for that group of frequencies. Turning the knob to the right (plus + side) boosts those frequencies, while turning that knob to the left (minus – side) cuts those frequencies. It’s always a good idea to “cut before boost.” That is, try to remove an offending frequency rather than boosting a bunch of other frequencies. One example might be to cut out some of the bass frequencies in a muddy sounding voice rather than boosting the mid-range to try and make it cut through the muddiness. Also, if you can’t hear a particular instrument well enough, rather than boosting 3,000 Hz to make it stand out, try to figure out what other instrument is getting in its way and cut 3,000 Hz out of the offending musician or singer. That way you reduce the potential for feedback in the PA system while increasing intelligibility of the mix… always a good thing. Equalization can be your friend or foe depending on how much control you take before you use it. Your goal is to use EQ in the church to make instruments/voices sound more intelligible and natural in the environment. Read the rest of this post 1 2 About Mike Mike Sokol System Designer & Audio Educator Mike Sokol does sound system design and training for JMS Productions, his consulting company in Western Maryland. Visit www.livesoundadvice.com for his educational articles and videos, and email him at [email protected] with comments and suggestions. http://www.livesoundadvice.com Comments Have something to say about this PSW content? Leave a comment! Cancel reply Scroll past the ”Post Comment” button below to view any existing comments. Your email address will not be published. Required fields are marked *Comment Name * Email * Website This site uses Akismet to reduce spam. Learn how your comment data is processed. Bob Palmatier says I have used a couple of articles from Mike in making changes and they were incredibly helpful. I really appreciate his willingness to share and educate us with his expertise Tagged with: Church Sound Consoles Engineer EQ Mike Sokol Processors Techniques Worship Audio · all topics Subscribe to Live Sound International Subscribe to Live Sound International magazine. Stay up-to-date, get the latest pro audio news, products and resources each month with Live Sound.