Church
Sponsored by
Yamaha

Bypassing Mr. Murphy: The Top 10 Ways To Get – And Stay – Connected

Thanks to Murphy's Law, any cable failure will likely occur during the most important moment in your worship service...

By Mike Sokol November 9, 2018

"Learning soldering skills is one of the best ways to get an entry level job in the pro audio business."

Few things are more frustrating in a sound system than an intermittent electrical connection. You all know the drill: everything seems to be working fine, and then it’s not.

These failures can range from an occasional crackle, to lowered volume levels, to even complete failure of a mixing bus or output connection with a total loss of sound. Sometimes the quick fix is to bang on the mixing console or jiggle the wires, but at best that’s just a temporary solution and the problem will likely rear its ugly head soon enough again.

Further, thanks to Murphy’s Law, the failure will likely occur during the most important moment in your worship service. What to do? Well, connection maintenance, of course.

Step 1: Have A Plan, Stan

Create a procedure to deal with intermittent cables and connectors. If there’s a microphone cutting out or crackling during a service, and replacing the XLR cable fixes it, do not let that suspect XLR cable migrate back into your inventory until it’s been repaired and tested.

I always put a piece of gaff tape over each end and throw it into a box with a label that says “Fix Me.” In addition, a sad smiley face on the label can be applied as well for that “pleading” look.

Step 2: Log It

Make a failure log to note when something goes wrong during a service. Many churches rely on volunteers who might do one worship service a month. If there’snot a way to pass on failure documentation to the next week’s crew, then you’re just kicking the can down the road.

The log can be as simple as a lined sheet hanging on a hook that you date, write in the failure information (i.e., channel 6 had a hum) and initial it. Even writing with a Sharpie on a piece of board tape and sticking it on the console goes a long way towards alerting other techs as to what to expect.

Step 3: Fix It

Don’t just fill up the box of cables that need to be fixed, make a date to deal with them at least once a month. That is, schedule a night where one or two sound team members go through the box and fix the problems.

This is also the time to look over the failure log carefully to see if there’s any patterns. For instance, one church I worked at would consistently have problems with the XLR cable feeding the lectern microphone. The male end connector, located in the floor, would have its wire pulled out and broken at least a few times every year.

It turns out that the stage crew would move the lectern out of place for the musical praise part of the service while forgetting to first disconnect the cable from the floor pocket. Using a long cable for this application instead of one just long enough, plus educating the stage crew with a sign asking them to “Disconnect Cable Before Moving” eliminated the problem.

Step 4: Test It

Ebtech Swizz-Army tester

Any cable that’s been repaired needs to be tested before it’s put back into service. This requires a quality cable tester.

My favorite is the Ebtech Swizz-Army 6-in-1 tester. Not only does it check XLR cables for mis-wiring, opens, and shorts, it can also be used to test instrument cables, MIDI cables, RCA cables, and any kind of adapters that might be in use. It also tests for a grounded XLR shield, one of the primary reasons you can’t break a ground loop hum from a direct (DI) box pin-1 lift.


Read the rest of this post

1
2
3


About Mike

Mike Sokol
Mike Sokol

System Designer & Audio Educator
Mike Sokol does sound system design and training for JMS Productions, his consulting company in Western Maryland. Visit www.livesoundadvice.com for his educational articles and videos, and email him at [email protected] with comments and suggestions.
http://www.livesoundadvice.com

Comments

Have something to say about this PSW content? Leave a comment!

Scroll past the ”Post Comment” button below to view any existing comments. Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.

Tagged with:

Subscribe to Live Sound International

Subscribe to Live Sound International magazine. Stay up-to-date, get the latest pro audio news, products and resources each month with Live Sound.