By Mike Sokol • November 7, 2017 Provided by Live Sound Advice. Every year, hundreds of musicians and audio techs suffer serious electrical shocks while on the job, and these incidents have the potential to be fatal. Therefore, it’s imperative to have a basic understanding of electricity to avoid possible electrocution, and further, this knowledge can help protect your equipment from going up in smoke. GFCI? No it’s not the name of an insurance company or a European sports car, GCFI is an abbreviation for Ground Fault Circuit Interrupter or G-F-C-I. They’ve been required in many localities for electrical outlets located near sinks and outdoors for the last 10 years or more. The two types of GFCIs you’ll encounter are either built into the power outlet itself (Figure 1, left) or inside the circuit breaker at the power panel (Figure 1, right). Both do exactly the same thing: they watch for electricity that’s going someplace it shouldn’t in an electrical Circuit by way of a Fault to Ground and then Interrupt the flow by tripping the circuit breaker. Rearrange the letters and you get G-F-C-I for Ground Fault Circuit Interrupter. That’s how the name is derived. Why Do We Need A GFCI? The heart muscle of humans is very sensitive to electrical shock. While it takes around 8/10ths of an amp (800 milliamperes) of current to power a 100-watt light bulb, it takes about one percent of that same current (10 milliamperes or so) to send your heart into fibrillation, causing death by electrocution. Figure 1. (click to enlarge) That’s why the NEC (National Electrical Code) now requires a special type of circuit breaker for damp locations that can tell the difference between the normal currents feeding an electrical appliance and the currents accidentally flowing through you to ground. And while a GFCI sometimes trips unexpectedly, it’s really there to save your life and the life of your appliances and other electrical components. How Does A GFCI Work? It’s a pretty ingenious system that uses a small current transformer to detect an imbalanced current flow, so let’s use our water pump analogy to review the typical current path in a standard electrical circuit. Figure 2. (click to enlarge) As you can see from Figure 2, we have our pump and turbine system again. And let’s imagine the pump at the top is pushing 7 Gallons Per Minute (GPM) of water current around in a circle that our little turbine at the bottom is happily using to spin and do some work. I’ve added flow meters at the bottom left and right of the illustration so we can keep track of these currents. Now since our pipes have no leaks, the current going out of the pump from the black pipe will exactly equal the return current coming back in the white pipe. And this will be an exact balance since no water is lost in this closed loop. That is, if 7.000 GPM (Gallons Per Minute) of water are flowing out of the black pipe, then 7.000 GPM will be returning to the pump via the white pipe. There are no water losses in this perfect system. Keeping In Balance Let’s add an extra meter in this system so we can keep track of the water flow a little easier (Figure 3). Notice there’s now a center meter that will show you the difference in flow between the other two meters. If the left and right meters show exactly the same water flow, the center meter will show zero GPM of flow by centering its needle. Figure 3. (click to enlarge) This is exactly what should happen in an electrical circuit that’s working properly. That is, if a light bulb has exactly 1 amp of current flowing out from the black (hot) wire, then exactly 1 amp of current should be flowing back in the white (neutral) wire. And an electric griddle that has 10 amps of current flowing out the black wire should have exactly 10 amps of current flowing back in the white wire. If there’s nothing wrong in the light bulb or griddle circuit, this electrical current balance will be pretty close to perfect, out to at least 3 decimal places. That is, 10.000 amps of current flow going out will equal 10.000 amps of current flow coming back in. Out Of Balance Now I’ve added a leak in the black outgoing pipe via the red pipe sticking out to the left (Figure 4). You can see from the red pipe’s meter that 5 GPM of water is flowing out onto the ground. And since only 7 GPM of water is coming out of the black pipe on the pump, there can be only 2 GPM of water returning into the white pipe on the right. Figure 4. (click to enlarge) Those 5 GPM of imbalance show up in our center balance meter, which alerts us to the fact that there’s a leak somewhere in the system. Now, we really would like to know about small leaks as well, so that center meter will tell us about an imbalance down to very small drips, say less than 1/1000 of a GPM. The same is true of our electrical circuit where we’re interested in currents in the 1/1000 of an ampere range (1 mA or 1 milliampere). That’s because just a few milliamperes of misdirected current flow is close to the danger level for stopping your heart. Teeter Totter In an electrical system, a similar type of detector is used at the center of the circuit which is acting like a balance beam. So if 7 amps of current shows up on both sides of the balance, then the beam will be exactly level. Figure 5. (click to enlarge) However, put 7 amps of current on the left side and 2 amps of current on the right side, and that 5 amps of imbalance will tip the scales, just like the teeter totter ride you took with your dad when you were maybe 50 years younger and a 150 pounds lighter (Figure 5). In our GFCI circuit this is a much more sensitive balance beam that only needs 5 mA (5 milliamperes or 0.005 amps) of current imbalance to tip over rather than the 5 GPM we’ve shown in the water pump illustration. The reason for needing this much sensitivity is that our hearts can go into fibrillation from just 10 mA of AC current flow, so we would like to detect and stop that flow before it stops your heart. Putting It All Together So here’s where it all comes together. Notice that our guy is unwisely touching a hot wire with a hand while his foot is in contact with the earth (Figure 6). And while the electrical outlet might have been supplying 7.000 amps of outgoing current to an appliance with exactly 7.000 amps of return current, there are now 7.005 amps going out and only 7.000 amps coming back. Figure 6. (click to enlarge) Those extra 0.005 amps of current (5 milliamperes) are taking a side trip from his hand to his foot via the heart. And the current balance circuit inside the GFCI is sensitive enough to recognize that imbalance and trip the circuit open with as little as 5 milliamperes of current flowing someplace it shouldn’t be going. The click you hear when a GFCI trips is its spring loaded contact opening up and interrupting the current flow in the circuit before it causes electrocution. That’s the entire GFCI’s reason for existence, to save you from electrocution and keep the electrical system safe from damage. Pretty cool, eh? Also note that the GFCI doesn’t really need a direct ground connection via the ground wire to do its job. Yes, one is required to properly “earth” the entire circuit, but the current balancing act is only between the black and white wires going to the outlet. If the current flow in the white wire exactly matches the current flow in the black wire to within 5 mA (milliamperes), the circuit stays activated. If the current flow is unmatched by any more than 5 mA, say by someone touching a live wire and the earth at the same time, then the trigger circuit inside trips a little switch and the current flow is stopped. It’s that simple. All this means you should install GFCI breakers where required, and don’t remove or bypass them if there’s false “nuisance” tripping. That so-called false tripping hints there’s something else wrong in your electrical system that’s leaking out current to someplace it doesn’t belong. And fixing that electrical leak is important since if you get your body in the middle of the current leak it can shock or even electrocute you. Just a quick definition of the word “electrocution.” That’s death from being shocked. So none of you readers were “electrocuted” last night at a gig and reading this now. Unless you’re zombies, and that’s an entirely different thing… About Mike Mike Sokol Lead Instructor, Live Sound Co Mike is the lead instructor for Live Sound Co, an AV integration and installation company in western Maryland, and lead writer of the Live Sound Advice blog. He’s also a veteran audio educator as well as an adjunct professor at Shenandoah Conservatory in Winchester, VA. Visit www.livesoundadvice.com for Mike’s educational articles and videos. http://www.livesoundadvice.com Tagged with: AC Audio Basics Electronics Management Mike Sokol Power · all topics Subscribe to Live Sound International Subscribe to Live Sound International magazine. Stay up-to-date, get the latest pro audio news, products and resources each month with Live Sound.