Sponsored by

Studio Note: The Ins & Outs Of Mix Bus Compression

One of the problems with compressing too much is that it leaves the mastering engineer a lot less room to work

By Bobby Owsinski September 23, 2011

This is excerpted from Bobby's book Mixing And Mastering With T-RackS: The Official Guide.
This article is provided by Bobby Owsinski.

Generally you’ll find that most renowned mixers use the bus compressor to add a sort of “glue” to the track so the instruments fit together better, but that also means that they’ll actually use very little compression.

In fact, sometimes only a dB or two of gain reduction at the most is added for the final mix. That being said, many mixers will also offer their clients (artists, band members, producers and label execs) a more compressed version to simulate what it will sound like after it’s mastered.

This “client mix” is achieved by using a signal path across the mix bus that’s similar to what a mastering engineer would use, that is, a compressor that’s fed into limiter at the end of the chain to raise the level to a point similar to a mastered release.

Because the clients get used to hearing the “client mix,” it’s so easy to let bus compression get out of hand. One of the problems with compressing too much is that it leaves the mastering engineer a lot less room to work, and in the case of a track that’s “hyper-compressed”, virtually eliminates the ability for the mastering engineer to be of much help at all.

There are two times during the mix that you can insert your buss compression – when you first start the mix or towards completion. While the two choices might not seem all that different, you will get a slightly different result from each.

At The End Of The Mix
If you wait to insert the bus compressor later in the mix, (the way it’s been traditionally done), the compressor settings will be a little less aggressive since you’ve probably already inserted a pretty good amount of compression on the individual tracks.

click to enlarge

Usually it’s inserted at the point during the mix where most of your elements and effects have already been added to your mix and it’s now time to concentrate on balances.

One of the advantages of inserting buss compression towards the end is that if you don’t like the sound, you can easily substitute a different compressor or even eliminate it all together. It doesn’t take much (usually a dB or two) to make a sonic difference to where it’s at least a little bigger sounding.

At The Beginning Of The Mix
The other way is to insert the buss compressor right at the start of the mix and build your mix into it. Since this affects the dynamics of the mix right from the beginning, mixing this way might take a little getting used to, but it has some advantages.

First, the mix comes together a little quicker since it has that “glue” almost right away as a result.

Second, you’ll find yourself using a little less compression on the individual tracks. This has the secondary benefit of giving you greater control of the overall compression of the mix.

If you feel like there’s too much, it’s pretty easy to back off on the buss compressor to where you or your client feels better about it (if that’s what they’re looking for), where if you added it towards the end, sometimes the only way to dial it back is to tweak the individual instrument compression, which can take quite a bit of time and re-balancing.

The third thing is that the bus compressor tends to even out the levels of the individual instruments a lot so you need less automation. The downside of doing it this way is that if you decide you don’t like the sound of the compressor, the overall sound and balance of the mix can change a lot when you insert a different one.

When starting with the bus compressor in the signal path from the beginning of the mix, you’ll find that you’ll be using somewhat more compression – about three or four dB.

Bobby Owsinski is an author, producer, music industry veteran and technical consultant who has written numerous books covering all aspects of audio recording. For more information be sure to check out his website and blog.

About Bobby

Bobby Owsinski
Bobby Owsinski

Music Industry Veteran and Technical Consultant
Bobby Owsinski is an author, producer, music industry veteran and technical consultant who has written numerous books covering all aspects of audio recording. For more information and to acquire a copy of The Recording Engineer’s Handbook be sure to check out his website.


Leave a Reply

Your email address will not be published. Required fields are marked *

boby says

How do you design a web page that pays? First off, you need to determine who will be getting the pay-off. It could be you or the web visitor, or better yet, it could be both of you. For example, an informational web page will be valuable to a reader looking for information and valuable to you if you have affiliates, links to products, or other sites you want to promote. When building a web page or looking for a home based business, affiliate programs are worth considering because they add value to the site for the reader and can provide enough revenue for you to keep the site going

bh0-006 study guidecap study guidecapm study guidesccda study guideccdp study guidesccent exam questionccia study guideccie security exam questions|

saraanderson says

I am absolutely amazed at how terrific the stuff is on this site. I have saved this webpage and I truly intend on visiting the site in the upcoming days. Keep up the excellent work!
send flowers germany
send gifts to netherlands

Allen says

voice recorders - Spy Equipment UK, providers of quality spy equipment, Phone and Video Surveillance

GlassMan says

this is so exciting and informative for me really…I have been always a fan of innovation and new things in life so doin these kind of courses like CCNA, MCSE and other certifications which can not only help you for your future but also makes you unique in this field as well .. so by trying i am very happy to be part of this and want you guys to also have a look at them because once you will join it and have a study on these, you surely gona like it and appreciate the effort…this is all what I can say, rest of you will decide. thanks!!!
testking ccna
testking pmp
testking ccie

testking vmware
testking itil
testking cisco
testking ccnp

Tagged with:

Subscribe to Live Sound International

Live Sound International brings you information on a wide range of pro audio topics. Stay up-to-date, get expert tips, industry news, new products and technologies delivered.

Discover how to make smart use of today’s sound technology, Subscribe Today!

Latest in Studio