Study Hall
Sponsored by
Audio Technica

Church Sound: Identifying Signal Flow Differentiation Between VCAs, DCAs & Subgroups

The methods in which channels can be grouped together

By Chris Huff January 16, 2013

A subgroup, by any other name…works differently.
This article is provided by Behind The Mixer.


Analog and digital mixers allow for controlling multiple channels as if they were one. 

These controls are commonly known as subgroups…but not really…maybe in the generic sense…but then you might say VCA’s if that’s what your board uses…because subgroups are different. [Sigh] 

There are several methods in which channels can be grouped together. And each works differently, of course, ’cause some days things just have to be complicated. 

Maybe I’m just in one of those moods…

Why Group Channels?

Channels can be grouped for a variety of reasons:

—Aux send groups.
For example, you might only want specific channels to go to a recording device or to the nursery or to the hallway loudspeakers or, more likely, to an effects unit where, say, you have reverb on all your vocalists.

—Volume channels. I’ve mentioned this one a lot. I will place my singers in a group and my instruments in another group. Such grouping gives you an easy way to pull back instruments for a more intimate feel or whatever you want to do.

Using such volume groups, the blend of the sounds within a group doesn’t change, only their overall volume. Drums are ideal for grouping with multiple microphones.

— Mute groups. For example, you might have the band in a mute group so when the music ends, you can mute all of their channels at once. This way, you avoid broadcasting the pop of the unplugged guitar or other such sounds you’d rather everyone not hear.

In this case, activating a mute group mutes all of the assigned channels. Mute groups are different than the other groups in how they work but since I’m talking grouping, I thought I’d mention it.

How Group Volume Controls Work Differently

The “normal” subgroup control can be considered the lazy* person’s way of controlling multiple signals. Take four channels and send their signals to a summing amp. When you move that group fader up and down, you are increasing or decreasing the volume of that summed sound. 

*I’m not against lazy; there is a time and a place for everything.

The VCA (voltage-controlled amplifier) is the busy person’s way of controlling multiple signals. Take four channels and send their signal to one fader.  Every time you increase the volume of that group fader, the group control sends a message back to those channels so each channel increases the volume coming out of it. A VCA is more like a remote control.

And if that’s not enough, let’s add in the DCA. The DCA (digital-controlled amplifier) works much like it sounds; instead of altering the actual signals from the channels, they are processed in the same way which then leads to increased or decreased volume.

Is There An Advantage Between Subgroup Types?

Glad you asked. I guess I am in one of those moods.

The “normal” subgroup is good for adjusting the volume of the grouped channels and sending that level out to the main mixer faders. That being noted, the volume levels of those individual channels stay the same as far as their signal being sent to other locations such as a post fader mix like a reverb unit. 

Lowering the normal subgroup fader, you could still hear those channels going through your reverb unit. In which case, you’re back to using more than one control for working with a group of channels.

The benefit of the VCA/DCA group is that when you lower the volume on the VCA channel, it’s lowering the output of each channel. Therefore, any post fader mixes, like the reverb units mentioned, are equally affected. You are preserving the dry/wet balance of the reverb effect.

The Take Away

The first time I started throwing around the word “subgroup,” a fellow tech said to me, “but VCA’s work differently.”  It was like they opened up a whole new side of the technical realm – just because it looks the same doesn’t mean it does the same.

Standing in front of your mixer, you are in control of a gigantic musical instrument. Like any great musician, you must know how each part of your instrument (mixer) works. Subgroups, VCA’s, and DCA’s control the volume of your channels at different points. Knowing how your mixer works with grouped channels, you know what other work you may or may not have to do for controlling your sound.

Next time I’ll present a new way of setting channel assignments on your mixer for better workflow management. It’s one I learned just weeks ago.

Ready to learn and laugh? Chris Huff writes about the world of church audio at Behind The Mixer. He covers everything from audio fundamentals to dealing with musicians, and can even tell you the signs the sound guy is having a mental breakdown. To view the original article and to make comments, go here.

About Chris

Chris Huff
Chris Huff

Chris Huff is a long-time practitioner of church sound and writes at Behind The Mixer, covering topics ranging from audio fundamentals to dealing with musicians – and everything in between.


Leave a Reply

Your email address will not be published. Required fields are marked *

Tagged with:

Subscribe to Live Sound International

Subscribe to Live Sound International magazine. Stay up-to-date, get the latest pro audio news, products and resources each month with Live Sound.

Latest in Church