Sign up for ProSoundWeb newsletters
Subscribe today!

Why Not Wye? When Combining Two Signals Into One Is Not A Good Idea
Anything that can be hooked-up wrong, will be. You-know-who said that, and she was right.
+- Print Email Share RSS RSS

This article is provided by Rane Corporation.

 

Wye-connectors (or “Y”-connectors, if you prefer) should never have been created.

Anything that can be hooked-up wrong, will be. You-know-who said that, and she was right.

A wye-connector used to split a signal into two lines is being used properly; a wye-connector used to mix two signals into one is being abused and may even damage the equipment involved.

Here is the rule: Outputs are low impedance and must only be connected to high impedance inputs—never, never tie two outputs directly together—never.

If you do, then each output tries to drive the very low impedance of the other, forcing both outputs into current-limit and possible damage. As a minimum, severe signal loss results.

“Monoing” Low End
One of the most common examples of tying two outputs together is in “monoing” the low end of multiway active crossover systems. This combined signal is then used to drive a subwoofer system.

Since low frequencies below about 100 Hz have such long wavelengths (several feet), it is very difficult to tell where they are coming from (like some of your friends). They are just there—everywhere.

Due to this phenomenon, a single subwoofer system is a popular cost-effective way to add low frequency energy to small systems.

So the question arises as how best to do the monoing, or summing, of the two signals? It is done very easily by tying the two low frequency outputs of your crossovers together using the resistive networks described below.

You do not do it with a wye-cord.

Summing Boxes
Figure 1 shows the required network for sources with unbalanced outputs. Two resistors tie each input together to the junction of a third resistor, which connects to signal common. This is routed to the single output jack.

Figure 1. Unbalanced Summing Box

The resistor values can vary about those shown over a wide range and not change things much. As designed, the input impedance is about 1k ohms and the line driving output impedance is around 250 ohms.

The output impedance is small enough that long lines may still be driven, even though this is a passive box. The input impedance is really quite low and requires 600 ohm line-driving capability from the crossover, but this should not create problems for modern active crossover units.

The rings are tied to each other, as are the sleeves; however, the rings and sleeves are not tied together. Floating the output in this manner makes the box compatible with either balanced or unbalanced systems.

It also makes the box ambidextrous: It is now compatible with either unbalanced (mono, 1-wire) or balanced (stereo, 2-wire) 1/4-inch cables.

Using mono cables shorts the ring to the sleeve and the box acts as a normal unbalanced system; while using stereo cables takes full advantage of the floating benefits.

Stereo-to-Mono Summing Box
Figure 2 shows a network for combining a stereo input to a mono output. The input and output are either a 1/4-inch TRS, or a mini 1/8-inch TRS jack. The comments regarding values for Figure 1 apply equally here.

Figure 2. Stereo-to-Mono Summing Box

Balanced Summing Boxes
Figures 3 and 4 show wiring and parts for creating a balanced summing box. The design is a natural extension of that appearing in Figure 1.

Figure 3. Balanced summing box using XLR connectors
Figure 4. Balanced summing box using 1/4-inch TRS connectors

Here both the tip (pin 2, positive) and the ring (pin 3, negative) tie together through the resistive networks shown.

Use at least 1 percent matched resistors. Any mismatch between like-valued resistors degrades the common-mode rejection capability of the system.


Commenting is not available in this weblog entry.