In The Studio: Tips For Mixing Rap Vocals, Part 2 - EQ
Specific things to listen for and how to address them

April 11, 2012, by Matthew Weiss

recording
This article is provided by the Pro Audio Files.

 
In my previous article, Mixing Rap Vocals Part 1, we discussed the importance of having an end game for your vocal sound.

In this article I’m going to give you techniques for actually getting there.

I’ve read (too) many articles about mixing vocals. Cut 300 Hz, boost 2 kHz, compress 4:1, yada yada. Unfortunately these articles don’t actually give you any real resource – they simply speculate on generalities.

What I’m going to give you is specific things to listen for and how to address them. This article will focus on EQ.

MICROPHONES

A vocal recording is an interaction between the vocalist and the microphone. In order to treat the vocal we’re going to have to address both the character of the voice, and the character of microphone interacting with the voice.

Two common issues that arise from the microphone are low-end proximity build-up, and mid-range resonance.

Proximity Effect

When a vocalist gets too close to a microphone the low end will build up. If you have control of the tracking scenario, the optimal solution is to get the vocalist at the right distance from the mic.

In the mix, the best way to eliminate this is to use a high-pass filter. I recommend not doing this haphazardly – the weight of the voice is caught in that proximity mud.

Try using a gradual slope where the build up begins, or a medium slope to knock out the heavy build-up in conjunction with a low shelf or bell to ease off any residual build up in the higher bass range.

Mid-Range

Microphones also tend to be sensitive to the mid-range. It’s not uncommon for an airy-resonance to perk up somewhere in the 300—600 Hz range. Usually a couple 2 dB cuts at a narrow Q will suck that right out.

However, don’t make any cuts if there’s nothing there you want to get rid of! In fact – be very wary of this range – this is sort of the area where everyone wants to constantly cut – but that’s the body – the “thickness” of the voice. You want enough content here that the vocal feels “full”, but not so much that it feels “unmixed” or “sloppy.”

THE VOICE

Now we can start listening to the character of the voice. For most rap vocals we want a sound that’s both bright and forward, but has body and character. Attaining forwardness and brightness tend to go hand in hand.

An easy place to start is in the treble range. Obviously if you already have a bright vocal, don’t boost the high end. However, many vocals benefit from some kind of high shelf boost. The high end boost does not need to be supremely focused – in fact a broad boost is generally more effective.

I like shelves that have very gradual slopes – Pultecs, the UBK Clariphonic, Waves HLS or the LinEQ by Waves (using the non-resonant shelf) are all great choices. Of course, they’re also expensive choices. Most stock DAW EQs are pretty good these days, so don’t feel you need the most expensive equipment or plug-ins to get good results.

Sibilance

Now, I’m not a “mix by numbers” guy by any means – in fact I think this ideology is just setting you up for failure.

That said, I find a +4 dB shelf at 10 kHz on a vocal is a good starting place. That setting usually works immediately or gets me pretty close to where I want to be (for most recordings).

A well recorded vocal won’t sound too sibilant as a result, but many recordings (especially if the vocalist is naturally sibilant) will get a bit “essy.”

This is where de-essing comes in. I used to really struggle with de-essing, I didn’t like it.

My issue was that I was putting the de-esser at the end of my chain. If you feed an EQ’d high end into a de-esser, you just end up pushing the de-esser harder to get that sibilance down. If you de-ess before you EQ, you even out your high end before hand, so the compression artifacts are less substantial.

Presence

The presence range is usually next on my check list. Somewhere in the upper mids is the “excitement” and forwardness of the voice. It’s where all the mouth noise and articulations show up. Usually the tone isn’t too hard to find – once you get it, it literally jumps out at you. What’s tricky is getting the voice to be very forward without it becoming piercing and too midrangy.

The key to getting maximum forwardness with minimum annoyance is the Q – or the width of the EQ band’s boost. Remember you’re not just boosting a single frequency, but a range of frequencies.

If you are getting an annoying vocal tone from your upper-midrange boost, tighten up the Q until it goes away. Or, conversely, if you have a good boost going but the vocal is still smooth, see if you can stretch the Q, and when it gets to be too much, back it off some. Also, remember that a vocal in solo will sound more mid-rangy than a vocal in a full mix.

Mid-Range

The mid-range – everything above the bass and below the treble – is the character of the voice. The tones, the textures – it’s all in that mid-range. I encourage experimentation with a new voice. Do little boosts and cuts to just to hear what’s coming from the voice.

You may find little “personality” tweaks that can help make the voice identifiable. Perhaps it’s a raspy overtone like DMX or Xzibit, or a nasal quality like Snoop Dogg or Q-Tip.

Finding unique tones helps to give the vocal character. Of course, optimally the character is already there – and if it is – don’t force anything. Doing something to put your own “engineer’” stamp on it is a common mistake and often results in a poor mix.

Hi-Pass Filters

Lastly, there’s the bass. DO NOT HI-PASS JUST BECAUSE PEOPLE DO IT. When I record vocals, I will hi-pass at the preamp if I feel I need to attenuate the bass of a voice. That means if you get a vocal that I tracked to mix – it either doesn’t need a hi-pass, or it was already hi-passed. Hi-passing would be needless and detrimental. That being said, if it does benefit from a hi-pass, go for it.

Now, here’s a little tidbit – just because you hi-passed a signal doesn’t mean you can’t also boost the low end to get more body. One of my favorite mixing techniques which I’ve used on everyone from Speech of Arrested Development, to Gift of Gab, to Gorilla Zoe, is to hi-pass out the mud, then use a broad slope EQ to boost bass back in. That’s right, I’m cutting, and I’m boosting the low end. A dB or two goes a long way with your low-shelf boost.

CONCLUSION

I am giving you certain things to listen for – not necessarily certain things to do. If a vocal sounds great – don’t mess with it. You have to rely on what you are aiming to hear, not the processing. The key isn’t to do a lot of processing, but to do just the right amount of the right moves.

Also, these ideas apply to the vocal on it’s own merits – once we start bringing in the rest of the mix we may have to reassess our tone settings.

Matthew Weiss records, mixes, and masters music in the Philadelphia, New York, and Boston areas. Find out more about him here.

Be sure to visit the Pro Audio Files for more great recording content. To comment or ask questions about this article go here.



Return to articleReturn to article
In The Studio: Tips For Mixing Rap Vocals, Part 2 - EQ
http://www.prosoundweb.com/article/in_the_studio_tips_for_mixing_rap_vocals_part_2_-_eq